How to Install a Tub (Step By Step).
Book A Service CallThe writer is making a few great annotation related to How to Install a Bathtub in general in this article in the next paragraphs.

Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily accessible, the project can move easily; if you have to open a wall to remove the old tub and also place the new tub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have actually currently bought a new tub as well as don't need to alter the setup of your previous water system pipelines.
Your tools and also product list need to consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location in between the tap and the sink. Safeguard the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bath tub in the needed position. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level as well as adjusting the feet on the bathtub up until the spirit level reads level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been made use of at least once as this will resolve it right into its final setting.
Preparing for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack an inflexible seal, creating the water to pass through the wall surface between the bathroom and also the tiling, causing issues with moisture and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealer can split rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

I hope you enjoyed reading our piece on Installing A Bathtub. Thanks for spending some time to read through our blog. Enjoyed reading our posting? Please share it. Help another person check it out. Thanks so much for your time spent reading it.
Get Offer